AQL Inspection: How Clothing Quality Checks Work
Most clothing brands do not check every single piece in an order. Instead, they use an AQL inspection: a standard way to test a random selection and decide whether the whole order passes. If you work with factories, you will see the term AQL on quotes, contracts and inspection reports.
In this guide, we explain what AQL means, how to read an AQL table and which levels are common for clothing. It goes deeper into one part of our guide to quality control.
What AQL Means
AQL stands for acceptance quality limit, sometimes also called acceptable quality level. It comes from the international standard ISO 2859-1. The standard tells an inspector how many pieces to check in an order of a certain size, and how many defects are allowed before the order fails.
An AQL is not a promise about the exact share of defects in your order. It is a statistical sampling plan. It keeps inspections fair, quick and consistent, without checking every piece.
The Three Types of Defects
Inspectors sort every defect into one of three groups, each with its own limit:
- Critical defects make a product unsafe or illegal to sell, such as a needle left in a garment. For clothing, the usual AQL is 0, so not a single one is accepted.
- Major defects make a product unsellable or likely to be returned, such as a hole, a wrong size or a misplaced print. The usual AQL is 2.5.
- Minor defects are small flaws most customers would accept, such as a short loose thread. The usual AQL is 4.0.
Our overview of common garment defects shows typical examples of each type.
How to Read an AQL Table
An AQL inspection always follows the same steps:
- Find your order size, also called the lot size.
- Look up the sample size for that lot size, usually at General Inspection Level II.
- Check the acceptance number for your AQL level.
- Count the defects found. If the number is at or below the acceptance number, the order passes.
The table below shows common values for clothing orders, based on single sampling at General Inspection Level II:
| Order size | Pieces checked | Max major defects (AQL 2.5) | Max minor defects (AQL 4.0) |
|---|---|---|---|
| 91 to 150 | 20 | 1 | 2 |
| 151 to 280 | 32 | 2 | 3 |
| 281 to 500 | 50 | 3 | 5 |
| 501 to 1,200 | 80 | 5 | 7 |
| 1,201 to 3,200 | 125 | 7 | 10 |
Use these numbers as a guide. Always confirm the exact plan with your inspector, or check it with the AQL calculator from QIMA.

Which AQL Level to Choose
For most clothing brands, 0 for critical, 2.5 for major and 4.0 for minor defects is a sensible standard. Premium brands sometimes choose a stricter level for major defects, such as 1.5. A stricter level means a bigger sample and a higher chance of failing, so it also raises the cost.
Whatever you choose, agree on it in writing before production starts. Put it in your purchase order, with your approved pre-production sample as the reference. It is also a good topic to raise when you find a clothing manufacturer.
What Happens After the Inspection
You receive a report with the result, photos and a list of defects. If the order passes, you can approve the shipment. If it fails, the factory usually sorts and repairs the goods, followed by a new inspection.
Keep every report on file. If the same defect keeps coming back, update your tech pack with clearer instructions for the next order.
Frequently Asked Questions about AQL Inspections
AQL stands for acceptance quality limit. It is a sampling method from the ISO 2859-1 standard that sets how many pieces an inspector checks and how many defects are allowed before an order fails.
AQL 2.5 is the most common limit for major defects in clothing. Together with the order size, it sets the sample size and the maximum number of major defects for the order to pass.
A common standard for clothing is 0 for critical defects, 2.5 for major defects and 4.0 for minor defects.
It depends on the order size. At General Inspection Level II, an order of 281 to 500 pieces usually means checking 50 pieces, and an order of 501 to 1,200 pieces means checking 80.
A major defect makes a garment unsellable or likely to be returned, like a hole or a wrong size. A minor defect is a small flaw most customers would accept, like a short loose thread.
When a brand books a third-party inspection, the brand usually pays. Some brands agree with the factory that it pays for a re-inspection when the first one fails.
